Cycflix: Exercise Powered Entertainment

Cheesy title, I know but it got you to click. Basically this project uses an Arduino Nano connected to a stationary exercise bike to control the streaming of Netflix on a PC, I tried to get it to work with just a Raspberry Pi but I ran into problems with finding a browser which could stream Netflix on the Pi and controlling said browser with selenium. On Firefox, you need the Widevine extension which isn’t supported on the Pi so it couldn’t stream Netflix, I found a Chromium browser someone made especially for streaming Netflix on the Pi but Google stopped supporting the Chromedriver on the Pi so I couldn’t control it. I did find an old chromedriver but I couldn’t get it to work.

Here’s is the link  to the Instructables post detailing how I made it

Bluetooth Steering Wheel and Robot Blogged About On Hackaday

A few months back, I put up a post on Instructables about using my old Xbox Steering wheel to control my also old robosumo robot over Bluetooth, it didn’t get much love since posting it…until today when a short blog post was written about it on Hackaday, written by none other than theHackSmith himself. Now that video has become my most watched video on my YouTube channel. I’ve been subscribed to theHackSmith for about 3 years now and watched his subscriber base grow from 10’s of thousands to 1 Million, so its nice to get a bit of publicity so that not all of my posts are just hiding in a obscure part of the web.

Measuring Temperature From PT100 Using Arduino

I posted another Instructable, this time about reading the temperature from PT100 using an instrumentation and differential amplifier. There’s abundance of LM35 temperature measurement on the site so decided to post about the PT100, might come in handy for the students doing Instrumentation in my college in the future. Also gave Autodesk’s new Circuits.io a try, to see what its like. It lets you build circuits on a breadboard and simulate them, it can also simulate Arduino code but slowed the simulation down. It doesn’t let you add components to the circuit diagram, only the breadboard mode and because you can only move things in the circuit diagram it didn’t look as nice or as clear as what I built on LTspice. But the breadboard does look nice and is good for showing the circuit layout to beginners that can’t read circuit diagrams. My circuit  can be found here. It also lets you embed the simulation onto your Instructables post but it wouldn’t embed here.
full-arduino

Simple Heart Rate Monitor Using Reflective Sensor

So I’m sure all of you have seen one of theses at least once, most likely on a visit to a hospital, this device is called a pulse oximeter.20101916190410 This device measures your heart rate and oxygen levels in your blood. The way it works is but having two leds on one side of the finger, usually red and infra-red, and on the other side a phototransistor or light dependant resistor(LDR). When blood passes through your finger, a different amount of light reaches the light sensor and the output spikes because of this.

3494761408471723727You could use either the red or IR led for this but if you want to calculate the blood oxygen levels you’d need both. Oxygenated blood lets more red light through and deoxygenated blood lets more IR light through and by alternating the leds and comparing the outputs, you can calculate oxygen levels but in this project I’m just going to be measuring the heart rate.

I wanted to make a simple heart rate monitor so I used cheap components that I had lying around so it definitely isn’t the best heart rate monitor around but it works. From a bit of googling I found a few other people with the same idea, one being Scott Harden which built this device a few years ago that could also be used to record an ECG, his post about building it can be found here, he also has lots of other great projects give it a visit. I used his circuit as reference from mine, I didn’t have the exact same values for each component but choose ones that were close. My circuit can be shown below:

 

Continue reading

Measuring Displacements Using Accelerometers: Part 3- Testing And Video

EDITED 20/05/2017

In the last post I showed the results from a test of a few millimeters but that was one of the last tests I conducted, first I tested the output of the gyroscope compared to the angle moved which I talked about before, then tested measuring a linear movement, then a movement made up of both linear and angular movements and then finally I tested the device for its initial purpose. As I already discussed testing the output of the gyroscope, I’m going to talk about the linear movement tests. I tested the device ability to measure a linear movement by mounting the sensor on a rack of a rack and pinion controlled by a servo and by controlling the angle of the servo I could repeatedly move the sensor a known distance. I don’t have a picture of the actual setup but for a visual of it, I created it on CAD.

linear_test1.JPG

So the sensor in black was laid flat on the rack and moved varying distance and the output of the accelerometer was compared to the calculated movement. The movement was calculated by using the equation for the length of an arc that the gear moved, this would be translated to linear movement to the rack.
L(\Theta)=2*\pi*r (\frac{\Theta }{360})

Continue reading

Measuring Displacements Using Accelerometers: Part 2- Comparing Methods and Integration

In the last post I discussed the methods I looked into for cancelling the gravity vectors measured by the ACC, if you haven’t seen that I would recommend reading that first. The way I compared the two methods was by seeing how well they follow the raw acceleration signal from an angular movement, this was done by mounting the sensor on the side of a servo motor and moving between different angles with varying starting positions(in reference to gravity) and magnitudes of angle change. Below is the graph from a 5-degree movement.


The blue graph is the raw acceleration signal on the Z axis,red is the cos method and the yellow is the tan method, looking at the full graph(left picture) they seem to be overlapped and looks like they both follow the raw signal fairly well but in the zoomed in picture(right), both are slightly off the middle of the raw acceleration so neither seems better than the other, the Y axis showed the same result that neither stood out. I did another test where the angle change was 35 degrees and the result of the of the two axes is below:

Continue reading